The Log Home Maintenance Guide
$24.95 Now Available

Click Here to Learn More

Tips For Rotted Logs

For restoring log ends like the ones pictured and maintaining the natural gray patina of the logs.

1. First, use PeneTreat to saturate the logs and keep them from rotting any further.

2. Next, use LiquidWood to seal cracks and create an undercoating for the WoodEpox to adhere to.

3. Then, use new lumber or a piece of straight grained salvaged or similar material to cut a "plug" to fill the cavity.

4. Saturate the plug with PeneTreat.

5. After the PeneTreat has dried, coat the plug with Liquid Wood, insert the plug and use WoodEpox to finish filling in around the plug and the cavity wall.

Note you can use Liquid Wood and sawdust to create a putty or a paste to fill the cavity as well.

6). You can use a charcoal colored masonry pigment (available from masonry stores). Just add enough of the pigment to color the WoodEpox gray like the rest of the building. Just knead it in with the WoodEpox. Remember, you only have to color the last 1/2" of the end of the log.

7). Use an end coating like Sealtight 60 to seal the ends of the wood.

 

To add strength and stability to these log ends without replacing them with new crowns: Drill 1' from the log end back horizontally into the more stable wood and use 1' lengths of Fiberglass Reinforcement Rods to act as an internal strength pin. Use the Liquid Wood as a glue around the rod. You should use at least three rods per log.

 

To hide the end of the rods, you can cut a wooden end plug coated with LifeTime (LifeTime will turn the new wood gray to match the rest of the building).

 

Note You can also spray the entire building with LifeTime to keep it gray and preserve it from any further decay. What is really nice about the LifeTime is that it is a one time application. You can also use Dri-Seal as a water protection coat for the building. Other products that would work well in this respect is Woodguard and WR5 Clear.

This house was originally coated with house paint instead of a Log Home Finish. You can see where the logs have cracked or "checked" leaving open cracks in the paint for rain water to penetrate into the wood causing further rot. The density of the paint coating acts like a plastic sheeting that traps in moisture causing blisters and flaking paint. In winter when the logs freeze, the trapped moisture expands by becoming ice particles. This causes more subsurface damage making tiny cracks larger and allowing more space for water to penetrate farther into the log causing more damage. In the photograph, the dark area behind the pipe is totally rotted.

In a situation like this all of the paint needs to be removed with either a chemical stripper or blasted with sand or cob. The next step would be to cut out the rotted areas of wood and use PeneTreat to saturate the logs and keep them from rotting any further. If the rotted areas are relatively shallow, LiquidWood can be used to seal cracks and create an undercoating for the WoodEpox to adhere to. Next, apply the WoodEpox and form it so that it conforms to the rest of the log. Dry pigment can be added to WoodEpox to color it (especially if you will be coating with a stain). Allow to dry thouroughly, then apply a new finish.

If large portions of the logs are rotted away, you will either have to replace portions of the log with half-log inserts or replace the entire log. You may need the services of a professional log restoration contractor.

Osborn Buffing Brushes
80 grit brush used with either an angle grinder or car buffer to clean and polish logs. The nylon bristles are heavily impregnated with abrasives, which aid in the removal of rough bruises, pitch, and wood pulp. The brushes also work well on fuzzy or rough logs caused by powerwashing. Use the 6" brush on a 7" to 9" angle grinder with a 5/8" arbor. Use the 4" brush on a 4" angle grinder with a 5/8" arbor. Take care not to burn your logs when using the four inch brush. Brushes will last much longer if a car buffer is used due to the slower rotational speed. If you are using a 6" brush on a 4" grinder, expect to see the bearings go out of the sander. Note: Though these brushes are rated up to 6000 RPM, we suggest an operating speed around 1800 RPM. The slower speed will greatly prolong the life of the brush and will also minimize the possibility of burning the logs. Not intended for heavy sanding.

Log-Gevity™
Bio-Strip Gel Environmentally friendly multipurpose stripper, cleaner, refinisher, designed for exterior and interior use. Bio-Strip is biodegradable and does not require neutralizing. It is non-caustic and also performs as a tough task cleanser. Does not contain methylene chloride. Coverage: 50-100 sq. ft. per gallon.
1 gal. R012-LGBSB $52.41
5 gal. R012-LGBSC $256.98

Log-Gevity™
Citrus Log Stripper (GEL)
Contains no methylene chloride and no neutralizing is needed. The ph balance is non-damaging to logs, future finishes, wood, masonry, plastered walls or metals. Designed to remove multiple layers of finish, varnish, stains, latex, and oil paint. Recommended for log exteriors and interiors. It can also be used on fine furniture and cabinets. Remains moist and active longer, therefore penetrating more layers in one application. Gel covers 75-125 sq. ft. per gallon.
1 gal. R012-LGSGB $51.87
5 gal. R012-LGSGC $254.38

Peel Away 6 is a paint coating remover for logs. This is an environmentally safe, biodegradable, user-friendly paint remover that is specially formulated to remove multiple layers of paint from wood, brick, stone, cement, plaster, marble, metal, and fiberglass surfaces. Requires no special ventilating and does not contain methylene chloride. Average coverage is 50 - 75 sq. ft. per gallon. (This is a one-time application where many other strippers require reapplication several times over).
1 gal. P049-PEELAY#6-1 $56.00
5 gal. P049-PEELAY#6-5 $258.62